Attic Ventilation Calculator

To calculate attic ventilation, divide the attic floor area by 300 and multiply by 144 for square inches of net free vent area, then put half low at the soffits and half high at the ridge. A 40 × 30 ft (1,200 sq ft) attic needs 576 in² in total: 288 in² of intake and 288 in² of exhaust, about 16.0 ft of ridge vent and 8 soffit vents. Enter your attic and your vents' labeled net free area below.

Jump to your result ↓

Your project

in²

From the product label. Many ridge vents are 12 to 18 in² per foot.

in²

From the product label. It varies by size and type.

Results

Example job shown. Change the numbers to match yours.

Total net free vent area
576 in²
4.00 ft²
Intake (low, soffit) area
288 in²
Exhaust (high, ridge) area
288 in²

Vents to buy

Ridge vent length
16.0 ft
Soffit vents
8 vents
  • Assumptions used: ridge vent at 18 in² of net free area per foot and soffit vents at 40 in² each, as you entered them.
  • Net free area (NFA) is the open area of a vent after louvers and screens, which is smaller than its size. Use the NFA printed on the product. Split the area about 50/50, with the exhaust high up near the ridge (the IRC wants 40 to 50 percent of the vent area there for the 1:300 ratio), and keep insulation from blocking the soffits.

Blueprint

ridge 16 ft40 ft30 ft

576 in² of vent · 8 soffit vents

How this calculator works

Building codes (such as the IRC in the US) set the minimum attic ventilation as a ratio of the attic floor area to the net free area of the vents. There are two ratios. 1:150 is the basic rule: 1 square foot of vent for every 150 square feet of attic floor. 1:300 is allowed only when the exception in IRC R806.2 is met: at least 40 percent and not more than 50 percent of the vent area must be high in the attic (ventilators no more than 3 ft below the ridge), with the rest low at the eaves, and in climate zones 6 to 8 a Class I or II vapor retarder must also be installed on the warm-in-winter side of the ceiling. If you are not sure the exception applies to your roof, use 1:150.

A Class I or II vapor retarder is a layer that slows moist indoor air from reaching the attic: a sheet of polyethylene, or kraft-faced fiberglass batts installed with the paper facing the heated rooms, are common examples. Older editions of the code worded the two conditions as alternatives, and local codes differ, so check which edition your building department has adopted.

NFA (in²) = attic floor area (ft²) ÷ ratio × 144intake = exhaust = NFA ÷ 2

Worked example: a 40 × 30 ft attic (1,200 ft²) at the 1:300 ratio needs 1,200 ÷ 300 = 4 ft², or 576 in², split into 288 in² of soffit intake and 288 in² of ridge exhaust. At 18 in² per foot, the ridge vent is 16 ft long, and soffit vents with 40 in² each need 8 vents. At the basic 1:150 ratio the numbers are about double: 1,152 in², a 32 ft ridge vent and 15 soffit vents (14.4 rounded up).

Assumptions and sources

The assumptions behind your numbers (waste, sizes, rates) are listed in the notes directly under your results, and they update when you change an input.

The formula and a worked example are shown above, so you can check any result by hand. Read how we calculate and check our numbers. Results are estimates for planning: supplier products vary, so check the size printed on the label.

Attic ventilation by attic floor area

Net free area (NFA). Ridge vent at 18 in² per foot and soffit vents at 40 in² each; your products' labels may differ.

Attic floorTotal NFA at 1:300Ridge vent (1:300)Soffit vents (1:300)Total NFA at 1:150
600 sq ft288 in²8.0 ft4576 in²
800 sq ft384 in²10.7 ft5768 in²
1,000 sq ft480 in²13.3 ft6960 in²
1,200 sq ft576 in²16.0 ft81,152 in²
1,500 sq ft720 in²20.0 ft91,440 in²
2,000 sq ft960 in²26.7 ft121,920 in²
2,500 sq ft1,200 in²33.3 ft152,400 in²

Tips before you buy

  • Ventilation protects the roof from moisture in winter and reduces heat build-up in summer, which prolongs the life of the shingles and lowers cooling costs.
  • Balance matters more than quantity. Exhaust without intake pulls conditioned air from the house, and intake without exhaust just stalls.
  • Do not mix different kinds of exhaust vents (such as a ridge vent and a gable vent, or power fans), because they can short-circuit each other.
  • Keep baffles (rafter vents) in place so insulation does not block the soffit airflow.
  • Local codes decide the ratio you must meet, so check with your building department.

Tools & materials for this project

Affiliate links As an Amazon Associate we earn from qualifying purchases. These links do not change what you pay.

Frequently asked questions

How much attic ventilation do I need?

The standard is 1 ft² of net free vent area for every 150 ft² of attic floor, or 1 per 300 where 40 to 50 percent of the vents are high near the ridge and the rest low at the eaves (and, in cold climate zones 6 to 8, a Class I or II vapor retarder is on the warm side of the ceiling). Always split the area between intake and exhaust.

What is net free area?

The actual open space that air can flow through, after you subtract louvers, screens and baffles. It is printed on the vent packaging, and is always smaller than the vent's overall size.

Is a ridge vent better than a gable vent?

A ridge vent combined with soffit intake gives the most even airflow, and is generally the best system. Gable vents rely on the wind and ventilate only part of the attic.

How do you calculate attic ventilation?

Attic floor area ÷ 300 × 144 = square inches of net free area, under the 1:300 rule (IRC R806.2 when 40 to 50% of the vents are high, or there is a ceiling vapor retarder); otherwise use 1:150, which doubles it. For 1,200 sq ft that is 576 in² at 1:300 or 1,152 in² at 1:150. Split it half intake, half exhaust.

How much ridge vent do I need for a 1,500 sq ft attic?

About 20.0 ft of ridge vent rated 18 in² per foot, for the 360 in² exhaust half of 720 in² at 1:300, with 9 soffit vents of 40 in² for the intake. Use the net free area printed on your vents, not their overall size.

Add this calculator to your website

Running a blog, a contractor site or a class page? You can put this calculator on it for free. Copy the code below, and please leave the link underneath the calculator in place. The small script just resizes the frame to fit the results; if your site strips scripts, the calculator still works inside a scrolling frame.

Get the embed code

Related calculators & guides

Estimates only. Results assume standard materials and simple shapes. Supplier products vary, and the final call on quantity, structure and safety is yours. Check your local code and your supplier's guidance before ordering.