Christmas Lights Circuit Load Calculator

Enter your circuit size and the watts printed on a strand. You get how many strands the circuit can safely run, and whether your plan is within the limit.

Jump to your result ↓

Your project

W

LED strands are often 2 to 10 W. Incandescent strands are often 40 to 200 W.

strands
W

Inflatables, a freezer, a garage, a heater: anything else the breaker feeds.

Results

Example job shown. Change the numbers to match yours.

Strands this circuit can run
288 strands
At 80% of the breaker rating
Safe continuous load
1,440 watts

Your plan

Planned load
100 watts
Current drawn
0.8 amps
Share of safe load
7 %
Verdict
Within the safe limit
Extension cord (single run)
16 gauge or heavier
  • Continuous loads like lights should stay at or below 80% of the breaker rating: 1,440 W on a 15 A circuit and 1,920 W on a 20 A circuit at 120 V. The strand maximum on the package may be lower than this, so follow whichever limit is smaller. This is a planning guide, not electrical advice.

Blueprint

120 V100 W0.83 Alimit 12 A

0.83 A on a 12 A limit

How this calculator works

A circuit is limited by its breaker: watts = amps × volts. A 15 amp breaker at 120 V is 1,800 W, but loads that stay on for hours should use no more than 80% of that: 1,440 W. A 20 amp circuit gives 1,920 W. Divide the safe wattage (after anything else on the circuit) by the watts per strand to get the number of strands.

safe watts = amps × 120 × 0.8strands = ⌊(safe watts − other loads) ÷ watts per strand⌋

Worked example: on a 15 amp circuit with nothing else on it, 1,440 W allows 288 LED strands of 5 W each, but only 8 incandescent strands of 175 W. Twenty LED strands draw 100 W, under 7% of the circuit.

Assumptions and sources

The assumptions behind your numbers (waste, sizes, rates) are listed in the notes directly under your results, and they update when you change an input.

The formula and a worked example are shown above, so you can check any result by hand. Read how we calculate and check our numbers. Results are estimates for planning: supplier products vary, so check the size printed on the label.

Tips before you buy

  • Always check the maximum number of strands that you can link end to end, printed on the package. It is a separate limit from the circuit.
  • Switching to LED lights makes the circuit almost a non-issue, while incandescent lights can overload a circuit with surprisingly few strands.
  • Hot or warm plugs, flickering, or a tripping breaker mean you are overloading something: unplug it and rethink the setup.
  • Use a GFCI outlet outdoors, outdoor-rated cords, and keep connections up off the ground and dry.
  • Never run a cord through a closed door or window, or under a rug, where it can overheat or get pinched.

Tools & materials for this project

Affiliate links As an Amazon Associate we earn from qualifying purchases. These links do not change what you pay.

Frequently asked questions

How many strands of Christmas lights can I plug into one outlet?

It depends on the strands. On a 15 amp circuit you can run about 1,440 watts: around 8 incandescent strands, or hundreds of LED strands, but the number printed on the strand for end-to-end connections is often lower.

How many watts is a strand of Christmas lights?

A 100-light LED mini strand uses 4 to 5 W. An incandescent mini strand uses about 40 W, and a 25-bulb incandescent C9 strand about 175 W.

Can I overload an extension cord with lights?

Yes. A 16 gauge cord is typically rated for 13 A at most, but long cords carry less. Use a heavier cord for long runs and high loads.

Add this calculator to your website

Running a blog, a contractor site or a class page? You can put this calculator on it for free. Copy the code below, and please leave the link underneath the calculator in place. The small script just resizes the frame to fit the results; if your site strips scripts, the calculator still works inside a scrolling frame.

Get the embed code

Related calculators & guides

Estimates only. Results assume standard materials and simple shapes. Supplier products vary, and the final call on quantity, structure and safety is yours. Check your local code and your supplier's guidance before ordering.