How Many Deck Boards for an 8x10 Deck?

An 8 × 10 ft deck (80 ft²) needs about 25 deck boards of 12 ft running the 8 ft way, in 22 rows across the 10 ft side, with 10% waste and 5½ in boards at 1/8 in gaps. That is 300 ft of board bought (25 × 12 ft). Run the boards the 10 ft way instead and it is 20 boards of 10 ft in 18 rows. Underneath it needs 7 joists at 16 in spacing (9 with the boards turned).

Jump to your result ↓

Your project

Usually the side along the house.

The direction joists run.

The real width of the board, not the name. A 5/4×6 or 2×6 deck board measures 5.5 in across.

The small space left between boards so water drains and wood can swell. Treated wood is laid nearly tight because it shrinks as it dries.

The length of the boards at the lumberyard. Longer boards mean fewer joints, but are harder to carry.

Distance from the middle of one joist to the middle of the next. 16 in is the usual choice; use 12 in for diagonal boards.

%

Covers cuts, bad boards and angled ends. Use 15% for diagonal decking.

Results

Example job shown. Change the numbers to match yours.

Deck boards to buy
25 boards
One 12 ft board per 8 ft row, plus waste
What to buy
  • JoistsEach as long as the deck width7 joists
  • Screws (2 per board at each joist)308 screws
Rows of decking across the width
22 rows
Board length bought (25 × 12 ft)Each 12 ft board leaves a 4 ft leftover piece that is too short for another row
300 linear ft
Deck surface to cover, rows × length (with waste)Net length laid on the deck, before leftover pieces
194 linear ft
Deck area
80 ft²
  • Assumptions used: 10% waste added; 5.5 in boards with a 0.125 in gap; joists 16 in apart; 2 screws per board at each joist.
  • If your boards are shorter than the deck length, plan for butt joints to land on a joist (use a double joist there), and add boards for the extra cuts.

Before you buy: round up to whole packs, check the size printed on the label, and add a little spare. Your supplier has the final say.

Blueprint

8 ft10 ft

25 deck boards · 7 joists

Boards for an 8 × 10 ft deck, by board length

An 8 × 10 ft deck suits a small seating area by a back door. With 5½ in boards and 1/8 in gaps, and the boards running the 8 ft way, the deck has 22 rows, which is 176 ft of decking before waste. These counts include 10% waste:

Board lengthBoards to buyTotal length bought
8 ft boards25200 ft
10 ft boards25250 ft
12 ft boards25300 ft
16 ft boards13208 ft
20 ft boards13260 ft

Which way do the boards run?

An 8 × 10 ft deck has two board counts, and both are right. Boards run across the joists, so the direction also sets how many joists there are and how long they are.

Boards runRowsBoards to buyJoists (16 in on center)Screws
The 8 ft way (this page)2225 of 12 ft7 of 10 ft308
The 10 ft way1820 of 10 ft9 of 8 ft324

To see the other layout in the calculator, swap the length and the width and pick 10 ft boards.

Waste and layout

LayoutWasteBoards run the 8 ft way, 12 ft boardsBoards run the 10 ft way, 10 ft boards
Straight, careful installer5%2419
Straight (typical)10%2520
Diagonal or picture-frame border15%2621

Joists and screws

Joists run the 10 ft width and are spaced along the 8 ft length.

Joist spacingJoistsScrews
12 in on center9396
16 in on center7308
24 in on center5220

That is just the decking surface, for an 80 ft² deck. Posts, beams, footings, ledger, railings and stairs are extra, and a permit is usually required.

Finishing the surface

Treated lumber should be left to dry for a few weeks to a few months, then cleaned and sealed. At about 200 ft² per gallon, one coat of stain or sealer on this 80 ft² deck takes about 1 gallon, more for the railings and steps (use the deck stain calculator). Composite decking needs no stain, but still wants cleaning.

Decks higher than about 30 inches off the ground, or attached to a house, usually need a building permit, an inspection and a guardrail. Check before you order.

An 8 × 10 ft deck: a small table and chairs

An 8 × 10 ft deck is 80 sq ft, so 25 boards of 12 ft stock with the boards running the 8 ft way, 7 joists at 16 in centers and about 308 screws. It fits a small table and chairs or a pair of loungers.

The 10 ft dimension suits 10 ft boards laid parallel to the long side, with nothing to cut off: that way the deck takes 20 boards of 10 ft on 9 joists. Board length matters at this size: compare the numbers for different stock lengths in the table and pick the one that leaves the least on the floor of the shop. Leave a gap of about a quarter inch between boards for drainage, and slightly more if the boards are wet when installed.

Want to change anything else? The calculator above is the full Deck Board Calculator: edit any number and the results update instantly.

Tools & materials for this project

Affiliate links As an Amazon Associate we earn from qualifying purchases. These links do not change what you pay.

Frequently asked questions

How many deck boards for an 8x10 deck?

It depends which way the boards run. Running the 8 ft way it is 25 boards of 12 ft (22 rows across the 10 ft side). Running the 10 ft way it is 20 boards of 10 ft (18 rows). Both use 5½ in boards with 1/8 in gaps and 10% waste.

How many joists does an 8x10 deck need?

At 16 in on center, 7 joists running the 10 ft width when the boards run the 8 ft way, or 9 joists of 8 ft when the boards run the 10 ft way. At 12 in it is 9, and at 24 in 5. Joist size and span must follow your local building code.

How many screws for an 8x10 deck?

About 308 screws with the boards running the 8 ft way, or 324 with them running the 10 ft way: two at every joist for each board. Buy a few extra, since they strip and get dropped.

Related sizes and guides

Estimates only. Results assume standard materials and simple shapes. Supplier products vary, and the final call on quantity, structure and safety is yours. Check your local code and your supplier's guidance before ordering.