Deck Board Calculator

Enter the size of your deck and the boards you plan to use. You get the number of decking boards to buy, the joists underneath, and the screws to fasten them.

Building in the UK? Use the UK (metric) version of this calculator.

Jump to your result ↓

Your project

Usually the side along the house.

The direction joists run.

The real width of the board, not the name. A 5/4×6 or 2×6 deck board measures 5.5 in across.

The small space left between boards so water drains and wood can swell. Treated wood is laid nearly tight because it shrinks as it dries.

The length of the boards at the lumberyard. Longer boards mean fewer joints, but are harder to carry.

Distance from the middle of one joist to the middle of the next. 16 in is the usual choice; use 12 in for diagonal boards.

%

Covers cuts, bad boards and angled ends. Use 15% for diagonal decking.

Results

Example job shown. Change the numbers to match yours.

Deck boards to buy
29 boards
One 16 ft board per 16 ft row, plus waste
What to buy
  • JoistsEach as long as the deck width13 joists
  • Screws (2 per board at each joist)676 screws
Rows of decking across the width
26 rows
Board length bought (29 × 16 ft)No leftover piece: the rows use the boards in full
464 linear ft
Deck surface to cover, rows × length (with waste)Net length laid on the deck, before leftover pieces
458 linear ft
Deck area
192 ft²
  • Assumptions used: 10% waste added; 5.5 in boards with a 0.125 in gap; joists 16 in apart; 2 screws per board at each joist.
  • If your boards are shorter than the deck length, plan for butt joints to land on a joist (use a double joist there), and add boards for the extra cuts.

Before you buy: round up to whole packs, check the size printed on the label, and add a little spare. Your supplier has the final say.

Blueprint

16 ft12 ft9 of 13 shown

29 deck boards · 13 joists

How this calculator works

Decking boards run across the joists. We work out how many rows of boards fit across the deck's width (each board plus its gap), multiply by the deck length to get total linear feet, add waste, and divide by the board length you will buy. Joists are counted at your spacing along the length, plus one for the end. Screws are two per board at every joist it crosses.

rows = ⌈width ÷ (board width + gap)⌉boards = rows × length × (1 + waste %) ÷ board length

Worked example: a 16 × 12 ft deck in 5.5 in boards with 1/8 in gaps: 144 in ÷ 5.625 = 25.6, so 26 rows. That is 416 ft of decking, 458 ft with 10% waste, or 29 sixteen-foot boards. With joists at 16 in you need 13 joists and about 676 screws.

Assumptions and sources

The assumptions behind your numbers (waste, sizes, rates) are listed in the notes directly under your results, and they update when you change an input.

The formula and a worked example are shown above, so you can check any result by hand. Read how we calculate and check our numbers. Results are estimates for planning: supplier products vary, so check the size printed on the label.

Tips before you buy

  • Buy boards in the longest length that suits your deck to cut down on butt joints, which are weak points and need to land on a joist.
  • Gap size matters: pressure-treated lumber shrinks as it dries, so lay it close to flush (1/8 in) while composite is gapped per the maker's instruction.
  • Fasteners: use screws rated for ground-contact treated lumber (coated or stainless), since cheap screws corrode and stain boards.
  • A deck that is attached to your house or high off the ground usually needs a permit and an inspection. The calculator only covers the surface boards and the joists.

Quick answers by size

Tools & materials for this project

Affiliate links As an Amazon Associate we earn from qualifying purchases. These links do not change what you pay.

Frequently asked questions

How many deck boards do I need for a 12x12 deck?

With 5.5 in boards and 1/8 in gaps, a 12 × 12 deck has 26 rows. That is about 312 ft of decking, or 343 ft with 10% waste. In 12 ft boards that is 29 boards.

How far apart should deck joists be?

Sixteen inches on center is standard for most decking. Composite and diagonal layouts often need 12 in. Span tables in your building code give the exact limit.

How many screws do I need per deck board?

Two per joist crossing. That works out to roughly 350 to 400 screws per 100 ft² with 16 in joist spacing.

Add this calculator to your website

Running a blog, a contractor site or a class page? You can put this calculator on it for free. Copy the code below, and please leave the link underneath the calculator in place. The small script just resizes the frame to fit the results; if your site strips scripts, the calculator still works inside a scrolling frame.

Get the embed code

Related calculators & guides

Estimates only. Results assume standard materials and simple shapes. Supplier products vary, and the final call on quantity, structure and safety is yours. Check your local code and your supplier's guidance before ordering.