How Much Concrete for an 8x10 Slab?

An 8 × 10 ft slab (80 ft²) poured 4 inches thick is 0.99 cubic yards exact, before waste (45 bags of 80 lb). Order 1.09 cubic yards of ready-mix or 49 bags of 80 lb mix, which adds 10% for spills and an uneven base. That is the figure the calculator below shows; change the thickness for a 5 or 6 inch slab.

Jump to your result ↓

Your project

Patios, walkways and shed pads are usually 4 in. Driveways are usually 5 to 6 in.

%

Forms flex and subgrades are never perfectly level. 5 to 10% is typical.

Results

Example job shown. Change the numbers to match yours.

Concrete needed
1.09 cubic yards
Includes your waste allowance
What to buy
  • 80 lb bags49 bags
  • 60 lb bags66 bags
  • 40 lb bags98 bags
Ready-mix to orderRounded up to the next ¼ yard. Ask your supplier about short-load fees
1.25 yd³
Cubic feet
29.3 ft³
Cubic meters
0.83 m³
Weight of the concrete neededFor the 1.09 yd³ above, at 150 lb per ft³
4,400 lb
Weight of the ready-mix you orderWhat the truck delivers: the order rounded up to the next ¼ yard, at 150 lb per ft³
5,063 lb
  • Assumptions used: 10% waste added; bag yields of 0.3, 0.45 and 0.6 ft³ for 40, 60 and 80 lb bags; 150 lb per ft³ for the weight.
  • Bag yields used: 0.60 ft³ per 80 lb, 0.45 ft³ per 60 lb, 0.30 ft³ per 40 lb. Check your bag, since brands differ slightly.
  • Ready-mix is usually ordered in ¼ yard steps. Round up rather than down.
  • In metric: an 80 lb bag is about 36 kg, a 60 lb bag about 27 kg and a 40 lb bag about 18 kg.

Before you buy: round up to whole packs, check the size printed on the label, and add a little spare. Your supplier has the final say.

Blueprint

8 ft10 ft4 in49 × 80 lb bags10 of 49 shown

1.09 yd³ · 49 bags

Concrete needed for an 8 × 10 ft slab, by thickness

These figures are for the whole 80 ft² slab. The last column adds 10% for waste, which is what we suggest you order.

ThicknessCubic feetCubic yards80 lb bags60 lb bagsYards with 10% waste
4 in26.70.9945601.09
5 in33.31.2356751.36
6 in40.01.4867891.63
8 in53.31.98891192.17

What an 8 × 10 slab is used for

An 8 × 10 ft slab is a common size for a backyard shed floor, or a small patio with a bistro set. Four inches is usual for a shed or patio. Heavy workshop equipment may call for 5 or 6 inches.

Bags or ready-mix for 8 × 10 ft?

At 1.09 cubic yards you are on the border. 49 bags of 80 lb mix is about 2.0 tons of dry material to mix and place before it sets. Many people still do it with a rented mixer and a few helpers, but get a ready-mix quote as well, since delivery fees and short-load charges can make the two options close.

Don't forget what goes under and inside it

A slab needs a compacted base, usually 4 inches of gravel, which for this size is about 1.19 cubic yards after allowing for compaction (see the gravel calculator). Reinforcement such as rebar or wire mesh holds cracks tight: the rebar calculator counts bars for an 8 × 10 ft grid.

Base, reinforcement and joints

At 4 inches thick the finished 8 × 10 slab weighs about 2.0 tons. Under it goes a compacted gravel base: 4 inches is about 1.2 yd³ of stone including 20% for compaction (1.7 tons). A grid of #3 rebar at 16 inch centers takes about 7 bars of 20 ft (53 lb).

Concrete cracks as it shrinks, so cut or tool control joints about 8 to 12 ft apart (a common rule is two to three times the slab thickness in inches, read as feet) to decide where. For this slab that means no joints, as it is small enough to pour as one panel.

Sizing an 8 × 10 slab for a shed

A shed floor frame has to sit flat, so pour the slab level and make it the size of the shed or a few inches larger on each side, so the walls land on solid concrete. At 80 sq ft and 4 in thick the job takes 1.1 cu yd, or 49 bags of 80 lb mix.

The forms are 36 ft long in total. If the shed has to be anchored, set J-bolts about 6 in from the edge while the concrete is wet, or plan to use concrete screws through the sill plates later. Keep water off the door side: the apron outside the doors should fall away from the slab.

Want to change anything else? The calculator above is the full Concrete Calculator: edit any number and the results update instantly.

Tools & materials for this project

Affiliate links As an Amazon Associate we earn from qualifying purchases. These links do not change what you pay.

Frequently asked questions

How many bags of concrete for an 8x10 slab?

For a 4 inch slab you need 45 bags of 80 lb concrete (60 bags of 60 lb), or 49 bags of 80 lb with 10% waste. For a 6 inch slab it is 67 bags of 80 lb, or 74 with 10% waste.

How many cubic yards is an 8x10 slab?

An 8 × 10 ft slab is 0.99 yd³ at 4 inches, 1.23 yd³ at 5 inches and 1.48 yd³ at 6 inches, before waste. Add 5 to 10% when you order.

How much does an 8x10 concrete slab weigh?

At 4 inches thick it weighs roughly 4,000 lb (2.0 tons), at about 150 lb per cubic foot. At 6 inches it is about 6,000 lb.

Related sizes and guides

Estimates only. Results assume standard materials and simple shapes. Supplier products vary, and the final call on quantity, structure and safety is yours. Check your local code and your supplier's guidance before ordering.