How Much Gravel for 200 Square Feet?

200 square feet of gravel at 3 inches deep needs 1.85 cubic yards, which is about 2.59 tons of crushed stone. The table covers other depths and pea gravel.

Jump to your result ↓

Your project

%

Add 10 to 15% for base layers that will be compacted, or if the ground is uneven.

$

Use your supplier's price. The default is an example.

Results

Example job shown. Change the numbers to match yours.

Gravel needed
2.59 tons
No waste allowance added
Cubic yards
1.85 yd³
Cubic feet
50.0 ft³
Weight
5,185 lb

Cost

Estimated cost$40.00 a ton (an example price, so use yours)
$103.70
  • Assumptions used: 0% waste and compaction allowance; 1.4 tons per yd³ for the material you chose.
  • Typical weights: about 1.4 tons per yd³ for crushed stone, 1.35 for pea gravel, 1.5 for road base. Ask your supplier for their exact figure, since moisture and size change it.

Blueprint

14.1 ft14.1 ft3 in

1.85 yd³

Gravel for 200 square feet, by depth

No waste added. Add 10 to 15% for a compacted base. Weights are for crushed stone at 1.4 tons per cubic yard and pea gravel at 1.35.

DepthCubic yardsTons of crushed stoneTons of pea gravel
2 in1.231.731.67
3 in1.852.592.50
4 in2.473.463.33
6 in3.705.195.00

Which stone, and how much?

Use crushed stone for anything that must lock together and carry weight (bases, driveways, paths). Pea gravel and river rock are decorative and shift underfoot, so keep them to a shallow top layer. Put landscape fabric underneath to stop the stone sinking into the soil. See tons per cubic yard for the weights of other materials.

How many loads is that?

5,185 lb of gravel is about 3 pickup trips, or a single small delivery. A half-ton pickup can carry about a ton of dense material at most, and often less, so check your truck's payload rating (on the sticker in the door jamb) instead of guessing.

If you are moving it by hand, 50 ft³ is about 17 wheelbarrow loads (about 3 ft³ each).

Two hundred square feet: a small patio base or a short driveway apron

200 sq ft at 3 inches is 1.85 cubic yards (2.59 tons). At a deeper 4 to 6 inches under pavers or a pad, the quantity rises quickly, so use the depth table to find your own total.

At this size a delivery truck is the sensible way to buy it: stone is cheap, but moving it is not. Ask the supplier to tip it as close as possible to where it will go, on a tarp, and leave a path for the wheelbarrow. A plate compactor, rented for a day, compacts each layer and is the difference between a base that stays flat and one that settles.

Want to change anything else? The calculator above is the full Gravel Calculator: edit any number and the results update instantly.

Tools & materials for this project

Affiliate links As an Amazon Associate we earn from qualifying purchases. These links do not change what you pay.

Frequently asked questions

How much gravel for 200 square feet?

At 3 inches deep, 1.85 cubic yards, or 2.59 tons of crushed stone. At 4 inches it is 2.47 yd³ (3.46 tons), and at 2 inches 1.23 yd³.

How many tons of gravel for 200 square feet at 4 inches?

3.46 tons of crushed stone (1.4 tons per yd³), or 3.33 tons of pea gravel. Add 10 to 15% if it will be compacted.

How deep should gravel be?

Two to three inches for decorative beds and paths over fabric, 4 to 6 inches (compacted) under patios and pavers, and 4 to 8 inches for driveways.

Related sizes and guides

Estimates only. Results assume standard materials and simple shapes. Supplier products vary, and the final call on quantity, structure and safety is yours. Check your local code and your supplier's guidance before ordering.