Concrete Calculator (UK, m³)

A 3 × 3 m base 100 mm thick needs 0.99 m³ of concrete with 10% waste, so you would order 1.00 m³ of ready-mix, or mix it yourself at 1:2:4 with 13 bags of cement (25 kg), 0.70 tonnes of sharp sand and 1.31 tonnes of 20 mm aggregate. Enter your own size below.

UK edition. In Canada or the US? Use the US and Canada version (feet, inches and US gallons).

Jump to your result ↓

Your project

Paths and patios are usually 100 mm. Driveways are 125 to 150 mm. Check what your plans or the Building Regulations require.

%

Uneven ground and spillage. 5 to 10% is typical.

Results

Example job shown. Change the numbers to match yours.

Concrete needed
0.99 m³
Includes your waste allowance
Ready-mix to orderRounded up to the next quarter m³. Ask your supplier about minimum loads
1.00 m³
Weight of concrete
2.38 tonnes
Area
9.0 m²

If you mix it yourself

Cement
314 kg
Bags of cement (25 kg)
13 bags
Sharp sand0.44 m³
0.70 tonnes
20 mm aggregate (gravel)0.87 m³
1.31 tonnes
  • Assumptions used: 10% waste added; DIY mix 1 : 2 : 4 by volume with a dry-volume factor of 1.54; cement 1440 kg/m³, sharp sand 1.6 and aggregate 1.5 tonnes/m³; concrete 2.4 tonnes/m³; 25 kg bags.
  • The DIY quantities are approximate: sand and aggregate bulk up with moisture, and the cement content of a "1:2:4" mix varies. For anything structural, use the mix design your supplier or engineer specifies. Concrete weighs about 2.4 tonnes per m³.

Before you buy: round up to whole packs, check the size printed on the label, and add a little spare. Your supplier has the final say.

Blueprint

3 m3 m100 mm13 × cement bags10 of 13 shown

0.99 m³ · 13 bags

How this calculator works

Concrete volume is the area multiplied by the thickness, with the thickness in metres (100 mm is 0.1 m). We add your waste allowance, and multiply by 2.4 to get the weight in tonnes. One cubic metre of concrete is the same as 1,000 litres.

m³ = length (m) × width (m) × thickness (m) × (1 + waste %)

To mix it yourself, the dry materials pack together when they are wetted, so you need about 1.54 times the finished volume of dry materials. A 1:2:4 mix is 7 parts: one of cement, two of sharp sand and four of 20 mm aggregate. Cement weighs about 1,440 kg per m³, sharp sand about 1,600 and aggregate about 1,500.

Worked example: a 3 × 3 m patio base, 100 mm thick, with 10% waste: 9 × 0.1 × 1.1 = 0.99 m³, or 2.4 tonnes. To mix it yourself at 1:2:4 you need about 314 kg of cement (13 bags of 25 kg), 0.70 tonnes of sharp sand (0.44 m³) and 1.3 tonnes of aggregate (0.87 m³).

Assumptions and sources

The assumptions behind your numbers (waste, sizes, rates) are listed in the notes directly under your results, and they update when you change an input.

The formula and a worked example are shown above, so you can check any result by hand. Read how we calculate and check our numbers. Results are estimates for planning: supplier products vary, so check the size printed on the label.

Concrete for common slab sizes (10% waste)

In m³, for 100 mm and 150 mm thick slabs. Order ready-mix in the next quarter m³ up.

Slab size100 mm thick150 mm thickDIY cement bags at 100 mm
2 × 2 m0.44 m³0.66 m³6
3 × 3 m0.99 m³1.48 m³13
4 × 3 m1.32 m³1.98 m³17
5 × 4 m2.20 m³3.30 m³28
6 × 4 m2.64 m³3.96 m³34
6 × 6 m3.96 m³5.94 m³51

Concrete for common garden jobs

With 10% extra, and the cement for a 1:2:4 mix if you mix it yourself. For a shed base or footings, the matching calculator adds the sub-base or the pads. The sand and cement mix ratios guide covers the mixes.

JobConcreteCement (25 kg bags)Calculator
Patio or base 3 × 3 m, 100 mm0.99 m³13Concrete calculator
Base 2 × 2 m, 150 mm0.66 m³9Concrete calculator
Shed base 8 × 6 ft (2.4 × 1.8 m), 100 mm0.48 m³7Shed base calculator
6 deck footings, 300 × 300 × 400 mm0.24 m³4Decking calculator

Tips before you buy

  • Above about a cubic metre, ready-mix is usually easier and gives a more consistent result than mixing by hand. Ask about minimum loads and short-load charges, and have the ground, shuttering and helpers ready before the lorry arrives.
  • Lay concrete on a compacted sub-base, usually 100 mm of MOT Type 1, so that the slab is supported evenly and water drains away.
  • Reinforce slabs that carry vehicles: A142 mesh (6 mm bars at 200 mm centres) is the common choice for a driveway. Use movement joints to divide large areas into bays.
  • Check for buried gas, water and electricity services before you dig. The free LSBUD (LinesearchbeforeUdig) service shows what runs near you.
  • In England, paving more than 5 m² of a front garden with an impermeable surface needs permeable materials, or drainage to a lawn or border, otherwise it needs planning permission. Check with your council.
  • Do not pour in heavy rain or frost. Keep fresh concrete damp, or covered, for about a week so that it cures slowly.

Quick answers by size

Tools & materials for this project

Affiliate links As an Amazon Associate we earn from qualifying purchases. These links do not change what you pay.

Frequently asked questions

How much concrete do I need for a 3m x 3m patio?

A 3 × 3 m slab 100 mm thick is 0.9 m³, or 0.99 m³ with 10% extra, which is about 2.4 tonnes. Order 1 m³ of ready-mix.

How many bags of cement do I need per cubic metre of concrete?

For a 1:2:4 mix, about 13 bags of 25 kg per m³ of finished concrete (roughly 320 kg of cement), with 0.7 tonnes of sharp sand and 1.3 tonnes of aggregate. The exact figure depends on the mix.

How thick should a concrete base be?

100 mm is the usual thickness for paths, patios and shed bases, and 125 to 150 mm for a driveway. Always check your plans or the Building Regulations for structural work.

Is it cheaper to mix concrete myself or order ready-mix?

Mixing is cheaper per cubic metre for small amounts, but it is hard work and the quality varies. Past about a cubic metre, the labour and the risk of a stop-start pour usually make ready-mix the better choice.

How many bags of cement are in a cubic metre of concrete?

About 13 bags of 25 kg (317 kg) for a general-purpose 1:2:4 mix, and 17 bags for a stronger 1:1.5:3 mix, with 0.70 and 0.67 tonnes of sharp sand respectively.

How much concrete do I need for a shed base?

A 3 × 2.4 m base 100 mm thick takes 0.79 m³ with 10% waste: 11 bags of cement if you mix it yourself. The shed base materials list adds the sub-base and formwork.

Do I need concrete for a shed base?

Not always. A concrete slab for an 8 × 6 ft shed is 0.48 m³, but paving slabs, a plastic grid with gravel or a timber frame also work for many sheds. The shed base options guide compares the materials for each.

Add this calculator to your website

Running a blog, a contractor site or a class page? You can put this calculator on it for free. Copy the code below, and please leave the link underneath the calculator in place. The small script just resizes the frame to fit the results; if your site strips scripts, the calculator still works inside a scrolling frame.

Get the embed code

Related calculators & guides

Estimates only. Results assume standard materials and simple shapes. Supplier products vary, and the final call on quantity, structure and safety is yours. Check the Building Regulations and your supplier's guidance before ordering.